Skip to content

Honest ready dates and a call if anything changes: (559) 553-1933

Orosi · Cutler · Dinuba · Orange Cove

(559) 553-1933

ServicesFrame Straightening

Frame Straightening in Orosi, CA

When a hit bends the structure under your car, the panels won't line up and the car may not drive straight. We measure your vehicle against factory dimensions and pull it back into spec. You get a realistic finish date, and an update if hidden damage changes the plan.

Silver sedan with a crushed rear quarter clamped to a red frame machine, a chain running from the pulling tower, as a technician works beside it in a shop bay

What frame straightening fixes

Most cars today are built as a unibody. The floor pan, rails and pillars work together as one shell. A hard hit can shift that shell a few millimeters. You may not see it, but you feel it: doors that rub, a hood gap wider on one side, tires that wear on one edge.

Frame straightening puts the structure back where the factory put it. We anchor your vehicle, measure key points and pull in slow, controlled steps until the numbers match. Then the outer panels, suspension mounts and alignment have something true to sit on.

It is often one part of a larger collision repair. If the damage turns out to be skin deep, we'll tell you so and point you to dent repair or bumper repair instead.

What the work includes

Measuring before anything moves

We take readings at the factory reference points before a single pull. You see where your car is out and by how much.

Anchored, staged pulls

Your vehicle is clamped down so it can't shift. We pull in short stages and re-measure between each one. Metal pulled too fast can tear or go past the mark.

Sectioning when a rail can't be saved

Some kinked rails should be replaced, not straightened. When that's the right call, we show you why before we cut, and we follow the repair procedure for your make.

Suspension and mount checks

Strut towers, the engine cradle and control arm mounts get checked along with the rails. A bent part bolted to a straight frame still pulls the car.

Final measurement and alignment

We measure again when the pulls are done and record the final numbers. A wheel alignment follows so the car tracks straight.

Signs your car may need frame straightening

  • Uneven panel gaps

    The gap around the hood, trunk or doors is wider on one side. When the structure shifts, the panels move with it.

  • Doors that stick or won't latch

    If a door needs a hard slam after an accident, the opening it sits in may have moved.

  • Pulling or an off-center wheel

    An alignment that won't hold, or a steering wheel that sits crooked on a straight road, can point to a bent rail or mount.

  • One tire wearing fast

    A tire chewing up its inside edge faster than the others is worth a measurement, especially after a hit to that corner.

  • Wrinkles underneath

    Creases in the floor pan, a kink in a rail, or cracked seam sealer near a wheel well. A slide off a farm road into a ditch can do this while the outside looks fine.

How a frame job runs at our shop

  1. 1

    Call and pick a drop-off day

    Tell us what happened and what you're noticing. We set a day to bring your car in that works for your week.

  2. 2

    Teardown and measuring

    We remove damaged parts so we can see the structure, then measure. This is where hidden damage shows up, so the estimate is written after we can see it.

  3. 3

    A finish date you can plan on

    Once we know the extent, we give you a date we expect to hit. If a part is backordered or an insurance supplement is pending, we say so up front.

  4. 4

    Pulls, repairs and updates

    Straightening comes first, then any sectioning, then panel and paint work. If something moves the timeline, you hear it from us when we find out, along with a new date.

  5. 5

    Final check and pickup

    We re-measure, align and road test before we call you. At pickup we go over the before and after numbers with you.

What drives the cost of frame straightening

No two frame jobs price the same, because the cost depends on what the measurements show. We write the estimate after teardown, line by line, so you can see what each part of the job costs. If insurance is paying, the same estimate goes to the adjuster.

How far out it is
A rail a few millimeters off takes less time than one shifted an inch. More pulls and more re-measuring mean more labor hours.
Straighten or replace
Kinked or torn metal often has to be sectioned or replaced. New rails and the welding that goes with them add parts and labor.
Related damage
Suspension parts, mounts, panels and paint usually need work too. The frame is often one line on a bigger collision repair estimate.
Your make and model
Some vehicles use high-strength steel or aluminum that the maker says must be replaced, not pulled. Their repair procedures set what we can do.

Frame straightening questions

Something not covered here? (559) 553-1933

Is a car with frame damage ever right again?

If the structure is measured back to factory spec and repaired the way the maker calls for, it drives and protects you the way it should. The measurements are the proof, and we give you the final numbers. When damage is too severe to fix right, we tell you that plainly.

How long will my car be in the shop?

It depends on the damage and on parts. A simple pull adds less time than a rail replacement. We give you a date after teardown and update you if parts or insurance approval push it back.

Will my insurance cover frame straightening?

If the collision is covered under your policy, structural repair is normally part of the claim. We send the adjuster our measurements and photos, and file a supplement if teardown turns up more. Our Insurance Claims page explains how that works.

Can I drive my car in if the frame is bent?

Sometimes. If it steers straight, the lights work and no tire rubs, driving it in is usually fine. If it pulls hard, leaks fluid or a wheel is pushed back, have it towed. Tell us what you see when you call and we'll help you decide.

Will the repair show up when I sell the car?

It can, if an insurance claim or report notes structural damage. What we can do is fix it properly and keep the before and after measurements, so you have a record of the repair to show a buyer.

Dark blue regular-cab pickup with a glossy refinished hood reflecting clouds, parked on a wet concrete shop lot beside open bays and a paint booth with a masked car

Get it measured, then get a plan

Tell us what happened and we'll set a time to bring your car in from Orosi, Cutler, Dinuba or nearby. You'll know the finish date, and you'll hear from us if it changes.